MTD 46 PB 11C-J10G600 (2008) Handle, Wheels, Cutting hight adjustment Listas de piezas de repuesto y dibujos

Handle, Wheels, Cutting hight adjustment 11C-J10G600 (2008)

MTD Petrol mower 46 PB 11C-J10G600 (2008) Handle, Wheels, Cutting hight adjustment

Pos	Número de artículo	Descripción
1	749-04181	UPPER HANDLE
1A	749-04277A	HNDL:UPR:GULLWING:J-DECK
2	747-04338	BAIL:BRAKE:40/46 cm
2A	747-04503	BAIL:ENG:J-DECK GULLWING
3	746-04209	CBL:CONT:1075mm ERS
4	749-04328	HNDL:LWR:40/46
5	782-7627A	BOLT:EYE:M6
6	736-0668	WASH: FLAT: 6.4x12x1.6
7	712-0691	NUT:HEXLK:M6-1:NYLON:DIN 985
8	710-1719	BOLT:CRG:M8x1.25x50 DIN 603
9	736-0700	WASH:FLAT:8.4 x 16 x 1.60
10	736-0689	WASH:LOCK:B 8.4:DIN 6798
11	720-0368	WING NUT
12	710-04451	BOLT:M8x1.25x25 DIN 603
13	787-01487638	DECK:RD:46cm:PUSH
13A	787-01487668	DECK:RD:46cm:PUSH
13B	787-01487-RG	DECK:RD:46cm:PUSH
13C	787-01487691	DECK:RD:46cm:PUSH
14	787-01483637	HNDL:BRKT:PUSH:LH:40&46cm
15	787-01482637	HNDL:BRKT:PUSH:RH 40&46cm
16	710-1714	SCREW:HEX:M8X12 DIN 933-8.8
17	712-0692	NUT:HEXLK:M8-1.25 NYLON DIN985
18	710-1780	BOLT:CRG:M8x1.25x16 DIN 603
19	736-0758	WASH:BELL:25mmODx12.2IDx1.6
21	712-0431	NUT:FLGLK:3/8-16:GRF:TOP LK
22	741-0751	HEIGHT ADJUSTMENT BEARING
22A	741-04229	BRG:HGT ADJ
23	687-02127A	BRKT ASM:PIVOT:REAR
24	687-02138A	ADJUSTING ARM
25	687-02124	LEVER ASSY HGT J DECK
26	738-1172	SCR:SHLDR:.750 x.500 x 3/8-16
26A	738-1173	SCR:SHLDR:.750x.625x3/8-16
27	687-02051	LVR ASM:HGT:L0-WHL
28	687-02123A	PIVOT BRACKET
29	712-0431	NUT:FLGLK:3/8-16:GRF:TOP LK
30	736-3013	WASHER-FL
31	634-04236	WHL ASM:180mm x 39mm:BAR
31A	634-04400	WHL:COMP:180mm:IDLE:BB
31B	734-04175	WHL:COMP:180mm IDLE BAR BB
31C	634-04409	WHL:COMP:180mm:IDLE:SLV
32	712-04074	NUT:HEX:M10x1.25 DIN 985
33	731-05244	HUBCAP:7":OYSTERGRAY
33A	731-05912	HUBCP:WHL:7":MELON YELLOW
33B	731-06127	HUBCP:WHL:180mm:A:GRAY
33C	731-06296	WHEEL CAP
34	736-0741	WASHER:BLVL:.760 x 1.250 x.041
35	731-2422	CABLE GUIDE
36	726-04055	CBL:TIE:3.6 mm x 140 mm
37	736-0504	WASH:WAVE:.510x.750 x.017
38	720-0347637	FOAM GRIP